p align="justify"> Corrosion mastics;
Protective, mastics;
Compressed air;
Metal work piece;
Glue, etc.used in the process of bodywork:
Hammers;
Support;
Hydraulic pump;
Hydraulic wedges;
Rack;
Wrenches;
Brackets;
Straightening hammer;
adaptation to insert locks, glass, rubber;
Cylindrical clamp.
3.3 Flow chart for bus body repair ISUZU SAZ NP - 37
3.2 shows a flow chart on the bus body repair ISUZU »SAZ NP - 37.
Table 3.2chart for bus body repair
№Name and content of workplace of performanceSeats impactLabour capacity (person-minutes) Appliances, tools, devicesTechnical requirementsDisassembly body1Removing upholsteryinside the body10,8manually2Removing the fuel tankfrom above20,6manually3Washing and drying bodyFrom above, from below, inside11 , 2Elevatorbody should be washed with shampoo and blow dry. Residual moisture around the bumpers and door mirrors dry warm air from the vacuum cleaner.4Disassembly of the car bodyFrom above, from below10,9load-carrying conveyorOn a conveyor belt from the body remove the door boot lid, grille, electric buffer, glazing, fittings and other components and spare parts. To remove the units chassis with a body mounted on a car lift5Removing the door from the bodylaterally20,5manuallyTo remove the door, open it to the maximum possible angle and lock into position suitable fence or slings lifting mechanism. Disconnect lever limited door at the front of the bracket body and pull axis. Remove the door.6Removing glass lifting nicknamefrom above20,312х13, key, wedge, screwdriverLoosen the screws securing the top scenes; disconnect the rocker from the glass; raise your glass up; inhibit it in this position by means of a click timber interposed between the glass and the inner door panel flange; remove the two screws that secure; Unscrew the fixing screws and remove the window from the door windows.7Removing the sliding window on the door zadaysfrom above10,3manuallylower glass (broken glass at lower glass holder); Remove door trim; unscrew the screws that secure the cage to the wings; remove the upper guide groove detach the stand sliding window from above and from below; remove the rack on the door; remove dull glass with gasket; picking up the glass, remove it8Removal and dismantling door hingeslaterally20,5manuallyIn the event of a large backlash in the hinge loop to remove the door from the body, then disconnect from the door hinges and dismantle them.9Removing the front fenderfrom above10,212х13, key , screwdriverunscrew the screws on the right and left; unscrew the two nuts; forwards to remove buffer10Removing the hood and hood lockfrom above20,2key 12х13open the hood; unscrew the four bolts fastening the hood to the hinges; remove hood11Removing the front wingfrom above10,3remove the front buffer; lift the hood; Unscrew and remove the 5 screws along the top flange of the wing; unscrew one nut in the bottom of the rear wing; remove the grommet nut and washer; doors open at unscrew one bolt in the wing bolt and remove the gasket remote; Unscrew and remove the three bolts in the front, connecting flanges of the wings; remove the wing12Removing the grille mudguardsfrom above20,3key 12х13remove the front buffer; Unscrew the two screws and mudguard part to the sub-spars to unscrew the three screws securing the left and right front fenders with mudguard; open the hood and remove the two screws on the top panel mudguard to mudguard remove radiator grille13Removal and adjustment of the boot lid and the torsion barsfrom above10,4Adjustable wrench assembly shovelDismantling torsion perform when fortified in the open position the trunk lid (this can be done with wooden slats, struts) Remove the torsion bars on the support; mounting a shovel (or use a wrench) gently bring the movable end of the torsion bar out of engagement with the movable member and the loop is gradually moving blade, enable to take torsion free position; also release the second torsion bar. After this operation, if necessary, remove the lid of the trunk. Check condition of plugs torsion (by visual inspection) and the presence in them abundant lubrication. If necessary, a sleeve or is replaced by a new refill or grease.14Removing the instrument panelfrom above10,2wrenchTo remove the instrument panel must first dismantle the parts and components: 1. Strip inclined racks wind window by removing 3 screws. 2. Facing blowing wind window right and left, held spring holders, remove from the slots dashboard. 3. Re...
