move the bottom casing, taxiing column by removing the screws. 4. Remove the 2 screws on the steering column and disconnect the steering column from the instrument panel. 5. Remove the 2 screws on the instrument panel in the area of ???? the steering column from the steering column bracket. 6. Remove trim gear lever on the dashboard console. 7. Remove the 4 screws from the front ashtray and remove it. 8. Remove the 2 nuts to the dashboard console. 9. Unscrew 4 screws pos. 10 panel mounting in the top of the zone facing blowing wind window. 10. Unscrew 2 screws pos. 13, a bottom panel fastening the right and left corners of the side uprights. 11. 2 Remove the heater control knob, unscrew the two screws securing the trim panel and remove it. 12. Remove the lower left side of the front rack by removing 3 screws. 13. Remove bolt bracket relay block and remove the unit from the frets. 14. Unscrew all the screws that secure the wire bundle to the units and devices, disconnect all the connectors in the engine compartment. 15. Loosen sleeve fixing the wiring harness from the engine compartment. 16. Detach the instrument panel of the bulkhead, and disconnect hoses corrugated two lateral and one central nozzle blowing. 17. Remove the instrument panel along with a bundle of wires from the car.15Dismantling of the dashboard consolefrom above10,2wrench, key 9х121. Remove trim gear lever. 2. Unscrew 4 screws front ashtray and remove it. 3. Unscrew Peridium bolt to the floor console. 4. Remove the 2 nuts to the dashboard console under the ashtray. 5. Open the armrest and remove the cassette holder together with a rug. 6. Remove the 2 screws that secure the rear of the console to the floor inside the compartment armrest. 7. 2 Remove the pipe blowing the rear of the console. 8. Raise the parking brake lever to the top position. 9. Raise the rear of the console to remove the console from the studs instrument panel in the front. 10. Remove the console of the car.16Removing the motor heaterfrom above10,5wrenchRemove the lower right instrument extensions; disconnect the connector from the motor; unscrew the three screws; remove the motor rotor downwards; loosen the locking screw fastening the rotor and remove it from the motor shaft; loosen the two nuts and remove the drive motor and gasket17Removing heaterfrom above10,6Manually, wrenchmove to the far right lever mixer heater and drain the engine cooling system and heat exchanger; Unscrew the locking clamps and disconnect the inlet and outlet hoses from the heat exchanger tubes; remove the rubber seals tubes; loosen the bolt fixing flexible rod holders on tap; remove draft from the tap; Remove the handle and lever actuator; Remove the two screws and remove the trim actuator; Remove the instrument panel; loosen the two nuts heater; disconnect the wires from the motor; and resistance heater and remove heaterRepair bodyshell18Removal from the repaired place layers of paintfrom above10,9scraperRemove from the repaired space-gluing layers of upholstery, sound insulation and corrosion protection with a scraper or knife19Deformed metal removal with the damaged areafrom above10,6Scissors, chisel, hacksawObserve safety20Scraping metal edgesfrom above11,2file, emery wheel, skinCleaned to bright metal edges on the perimeter of the metal scraps21Pattern patchfrom above10,8scissors cutterPatch and carve out a place fit for a fully replaceable parts.22weldingfrom above11,5Gas-electric or gas burner with a fine fillerTo reduce war page weld metal place near the weld should smear raw asbestos.Assembling the body23heater installationfrom above10,6ManuallyHeater installation done in reverse order. After installing the heater and connect all hoses, refill the cooling system and heater.24Mounting console dashboardfrom above10,8manuallyThe mounting bracket to make in reverse order.25Installing the instrument panelfrom above10,5manuallyInstallation of the instrument panel in the reverse order to implement26Replacing the headlinerFrom below , laterally11,2Glue, scissors, cutterremove cover lighting, three handrail above openings and right rear doors, decorative edgings doorways, wall-pillars, brackets inside rear-view mirror and sun visors with visors, windshield and rear window, along with seals, tailgate trim shelves; Slightly moisten the edge of the roof lining gasoline in places gluing and 10-15 min gently separate them from the body; remove headliner together with arcs, bringing the ends of the arcs of holes side rails of the cover. Installation headliner start back. Please install back arc, and then pull the upholstery, consistently setting the rear arc, pulling upholstery, consistently setting the following arc. Before gluing upholstery remove the old glue.27Replacing windshield and rear windowLaterally, from above21,4Blade assembly, glue, mastic.release the seal from the adjacent nodes; to rear disconnect connectors glass. The rest of the o...
