rder of operations for the windscreen and rear window is the same: to remove the debris of shattered glass seal; carefully wooden click, separate petals seal (around the perimeter of both sides) from the opening of the body and remove the seal; clean and seal the body opening of the old mastic; fill with fresh mastic 51-G - 7 slot under glass in the seal; put the seal on the new glass and tuck into a groove seal decorative border; lay in a free slot seal around the perimeter of overlapping mounting cord (solid twisted rope diameter of 4-5mm), leaving the top of the loose ends about 400 mm long; Apply a continuous layer of sealing mastic 3-5 mm vertical opening window ledge; insert glass window opening so that the free ends of the mounting cord were inside the body. Perform this operation together: one person should press on the outside glass consistently in those places, where the skins pulled out, the other pulls the cord inside. Check the tightness of the windscreen, showering glass on the outside and seal water jet. If necessary, additional fluff found gaps with putty.28Installing windowsfrom above20,5Wedge, key 12х13, greaseCarefully place the glass with a holder assembly through the window opening in the door; install guide sliding window and simultaneously make them in glass; raise your glass hands in the uppermost position and hinder it in this position by a wooden wedge; make the door windows and fix it at five points screws; install guide (only for front doors) and fasten bolts top and bottom; fix the rocker bottom screws to the door, whilst ensuring that the slope of the scenes in the vertical plane of the trajectory matched glass; fasten upper connecting link to the glass cage screws; attach the holder to the cage with glass stones. Friction surfaces of both wings and the guide should be lubricated with grease.29adjustment windowfrom above20,4Key 12х13loosen the upper bolts holder, press the glass to the rear chute and fasten bolts; if this is not enough, loosen lower bolts guide 6i move forward until skew glass; Tighten bolts and check the operation window; if necessary, repeat the adjustment. Rotating the control window must be lowered and raised smoothly without jerking and jamming and securely held in any intermediate position.30Replacement and adjustment of the trunk lockfrom above10,3manuallyRelease cravings, get it out of engagement with the drive socket, unscrew the bolt lock and remove the locking rod. Use a screwdriver to disconnect the rod with a tip and then snap it on the replacement lock. Lock installation in the reverse order to check operation of the lock from the drive with the trunk lid open. Why Use a screwdriver to move the cam lock in position closed raquo ;, and click the drive. If the lock is open, the control rod is correct, if not, then it is necessary to release cravings, unscrew the tip 2 turns, fix and check again. After checking the boot lid can be closed by checking pre-engagement (contact) snap lock. To replace the drive also must be disconnected from the drive rod, to take her to the side, and by removing the 2 screws, remove the actuator. Make install drive in reverse order. Functional test drive conducted in the following order: put the cam lock to lock off the dog must securely hold the cam in engagement; put the drive in the open .31Installing torsion bars and coversfrom above20,5Adjustable wrench assembly shovelUpon cancellation of the drive on the open turn key clockwise by 45 degrees, and by pressing the drive, open the lock.32Mudguard assembly and installationfrom above20,8Key 12х13Mudguard grille assembly and install it in the reverse order33Installing the wingfrom above20,3manuallyTorsions and covers installation and perform the reverse sequence.34Mounting the hood and hood lockfrom above10,8manuallyMudguard grille assembly and install it in the reverse order35Setting bufferfrom above10,3manuallyInstallation in the reverse order36Adjusting door locksfrom above20,6Pencil, key 12х13lead castle in working order; note marker pencil clamp position; secure doors and inspected externally; note ceasing or protrusion of the door; its vertical movements; based on the previous decision on the magnitude and direction of displacement of the lock; unscrew 2-3 turns lock bolts and move it in the right direction; if necessary, repeat the above steps.37Laterally21,2Manually, scissors, cutter.After the necessary repair and adjustment work on the doors and door gaskets installation sites and upholstery in the reverse order verifying the integrity and accuracy of the pre-installation of the seal and sliding window.38Installing door trimFrom above, laterally20,5Allen key, screwdriverDestroyed when removing trim caps replace conditionally, pens with raised glass windows should be installed vertically downwards.39Installation of hinges on the pillarlaterally20,8Allen keyRepaired and greased hinges inserted into slit-like openi...
